C. Remove the flange nut (item 6) that secures driv-
en pulley (item 5) to groomer shaft. Remove driven
pulley from shaft. Locate and retrieve square key
(item 4) that locates driven pulley on shaft.
D. Press bushings into groomer plate until the bush-
ing contacts the shoulder in the groomer plate bore.
E. If groomer studs (not shown) were removed from
groomer plate (item 17), install new studs into
groomer plate and torque from 14 to 18 ft--lb (19 to
24 N--m).
D. Slide washer (item 3) and pulley spacer (item 2)
from groomer shaft.
E. Remove shoulder bolt that secures quick--up ball
joint rod to groomer plate (Fig. 10).
2
1
F. Disconnect extension spring (item 14) from stud
on groomer plate.
G. Remove two (2) socket head screws (item 7) that
secure groomer components to cutting unit side
plate.
H. Remove pivot hub and idler plate assembly from
cutting unit.
I. Support groomer shaft to prevent it from falling.
Carefully slide drive side groomer plate from groom-
er shaft and cutting unit. Remove groomer shim.
3
4
3
4
4
3.
To remove groomer plate assembly from groomer
non--drive side of cutting unit:
Figure 5
A. Remove hydraulic reel motor from cutting unit
(see Hydraulic Reel Motor Removal in the Service
and Repairs section of Chapter 7 -- Cutting Units).
1.
2.
Drive side groomer plate
Non--drive groomer plate
3.
4.
Bearing
Grease seal
B. Remove two (2) socket head screws (item 7) that
secure groomer components to cutting unit side
plate.
C. Remove pivot hub from cutting unit.
17
(23
to 21 ft--lb
to 28 N--m)
D. Support groomer shaft to prevent it from falling.
Carefully slide non--drive side groomer plate from
groomer shaft and cutting unit.
4.
plates. Remove and discard damaged or worn compo-
nents.
Inspect seals, bearings and bushing in groomer
3
2
Installation (Fig. 4)
1.
groomer plates, install new components noting proper
orientation as shown in Figure 5.
If seals, bearings or bushing was removed from
1
A. Pack bearings with grease before installation.
Figure 6
3.
B. Press bearings into groomer plate so that bear-
ings contact shoulder in groomer plate bore.
1.
2.
Groomer plate
Shoulder bolt
Quick--up ball joint rod
C. Install grease seals so that seal lips are posi-
tioned toward the groomer blade location. Seals
should be flush with surface of groomer plate.
Reelmaster 5010 Series
Page 8 -- 7
Groomer
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work