Groomer Reel Service
Inspect groomer reel blades frequently for damage and
wear.Straightenbentbladeswithapliers.Eitherreplace
worn blades or reverse the blades to put the sharpest
blade edge forward (Fig. 11). Blades thatare rounded to
the midpoint of the blade tip must be reversed or re-
placed for best groomer performance.
3
1
2
Disassembly (Fig. 12)
4
1.
Park machine on a clean and level surface, lower
cutting units completely to the ground, stop engine, en-
gage parking brake and remove key from the ignition
switch.
2.
Remove groomer reel from cutting unit (see Groom-
er Reel Removal in this section).
GROOMER
ROTATION
3.
4.
Remove excluder seals from groomer reel.
Figure 11
Ifgroomer reelisequippedwithbroomerkit(Fig.13),
remove straps and broomer brushes from reel.
1.
2.
Groomer blade
Location hole
3.
4.
Sharp edge
Dull (rounded) edge
5.
12).
Remove lock nut from either end of the shaft (Fig.
200 to 250 in--lb
(23
to 28 N--m)
6.
needed, remove second lock nut from shaft.
Remove spacers and blades from groomer shaft. If
1
2
3
4
7.
If necessary, remove groomer shaft ends from
groomer shaft.
Assembly (Fig. 12)
1.
first spacer and then first blade on shaft.
Install lock nut on drive end of groomer shaft. Place
5
CENTERED ON SHAFT
2.
Alternately install remaining spacers and blades
making sure that all blades are separated by a spacer.
Additionally, rotate location hole on each installed blade
one flat of the shaft, in a counterclockwise direction.
3.
spaceronshaftandthenthreadsecondlocknutontothe
shaft. Center blades on shaft with lock nuts.
When all blades have been installed, place final
4
4
5
1
3
2
Figure 12
4.
Using wrench on shaft flats to prevent shaft from
turning, torque second lock nut from 200 to 250 in--lb
to 28 N--m). After torquing lock nut, spacers should
1.
2.
3.
Groomer reel shaft
4.
Lock nut (2 used)
Excluder seal
Groomer blade (42 used)
Spacer (43 used)
5.
(23
not be free to rotate and groomer blades should be cen-
tered on shaft.
5.
positionbroomerbrushestoreelbladesandsecurewith
straps. Straps should be positioned between blades
Ifgroomer reelisequippedwithbroomerkit(Fig.13),
1--2,
14--15, 28--29 and 41--42. Pull straps tight and cut
off strap extension approximately 1/4” (6 mm) beyond
retainer.
Groomer
Page 8 -- 12
Reelmaster 5010 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro 5210, Toro 5410, Toro 5510, Toro 5610 |
| Download File |
|
| Document Type | Catalog, Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Lawn and Garden readers have rated Toro 06148SL Rev B Reelmaster 5210 5410 5510 5610 Service Manual 4.0 out of 4.0 based on 1 product reviews. i hope is going to work