Adjustments
Traction Control Rod Adjustment (Serial Numbers Below 50000) (Fig. 12)
1.
wheels do not creep; refer to “Traction Drive Neutral Ad-
justment”.
Check traction drive neutral position to assure front
2.
(1.6
Depress traction pedal fully. There must be 1/16 inch
mm) between inside front edge of pedal and trian-
gular support brace. If distance is as specified, the con-
trol rod is adjusted correctly. If distance is not as
specified, proceed to step 3 for an adjustment.
3.
move cotter pin and slotted nut retaining tapered socket
in pivot mount on bottom of traction pedal.
Loosen jam nut away from front of control rod. Re-
4.
Adjust tapered socket as required. Slide end of ta-
pered socket through traction pedal pivot mount. Then
depress pedal and check for 1/16 inch (1.6 mm) clear-
ance between front edge of pedal and top of support
brace. Adjust tapered socket until correct adjustment re-
sults.
Figure 12
4.
5.
After control rod is adjusted correctly, secure tapered
1.
2.
3.
1/16 in. (1.6 mm)
Jam nut
Nuts
Friction wheel
5.
socket and traction pedal together with slotted nut and
cotter pin. Also tighten jam nut against front of control
rod.
Cotter pin & slotted nut
Traction Control Rod Adjustment (Serial Numbers Above 50000) (Fig. 12A)
1.
wheels do not creep; refer to “Traction Drive Neutral Ad-
justment”.
Check traction drive neutral position to assure front
.120”
(3.05 mm)
1
2.
Loosen lock nuts and adjust traction pedal stop screw
3” (76.2 mm)
to a length of 3” (76.2 mm).
3.
Rotate traction pump lever on transmission to full for-
ward speed location.
2
4.
Adjust traction control rod end until there is a .120”
mm) gap between top of traction pedal stop screw
and pedal.
(3.05
Figure 12A
5. Make sure that all nuts are properly secured after ad-
1. Traction pedal
2.
Stop screw
justment.
Traction Pedal Friction Wheel Adjustment (Fig. 12)
1.
Loosen two nuts securing traction pedal shaft on right
3. Tighten nuts to secure shaft and wheel in position.
side of pedal.
2.
away from underside of traction pedal.
Rotate shaft to relocate worn surface of friction wheel
Groundsmaster 300 Series
Page 5 – 23
Rev. G
Adjustments
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Groundsmaster 300, Toro Groundsmaster 328 D, Toro Groundsmaster 92801SL |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(2 votes, average: 5 out of 5) Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Need 328D. Manual pdf. Will rate after finding manual
t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems