Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Run Solenoid (Groundsmaster 328–D) (Solenoid With 2 Wire Connector)
The run (ETR) solenoid must be  energized for the en-
gine to run. The solenoid is mounted on the engine block
near the injection pump.
4.  Touch  a negative  (–)  test  lead from  the  12 VDC
source to the fuel stop solenoid frame (ground) (Fig. 13).
The solenoid should engage, making an audible “click,”
and the plunger should retract.
In Place Testing
5.
nal. The solenoid should stay engaged.
Remove positive (+) voltage from the pull coil termi-
Note:
Prior to taking small resistance readings with a
digital multimeter, short the test leads together. The me-
ter  will display  a  small resistance  value (usually  0.5
ohms or less). This resistance is due to the internal re-
sistance of the meter and test leads. Subtract this value
from from the measured value of the component you are
testing.
6.  Remove positive (+) voltage from the hold coil termi-
nal. The solenoid should release.
7.
Connect the wire harness connector to the run sole-
noid.
1.
solenoid.
Disconnect machine  wire harness  connector from
2
2.
Using a digital multimeter, touch one test lead to the
1
pull coil terminal and the other test lead to the fuel stop
solenoid frame (ground) (Fig. 13). The resistance of the
pull coil should be less than 1 ohm (but not zero).
3.
Using a digital multimeter, touch one test lead to the
3
hold coil terminal and the other test lead to the fuel stop
solenoid frame (ground) (Fig. 13). The resistance of the
hold coil should be approximately 15 ohms.
Figure 13
4.
Connect solenoid to the machine wire harness.
1.
2.
Fuel stop solenoid
Pull coil terminal
3.
Hold coil terminal
Live testing
1.
Disconnect wire  harness connector from  run sole-
noid.
Note:
The solenoid may be removed from the engine
or tested in place.
2.
sure that the solenoid plunger moves freely and is free
of dirt, debris and corrosion.
If the  solenoid is  removed from the  engine, make
Note:
When testing run solenoid, use test leads with
at least 14 gauge wire.
3.
source to the pull coil and hold coil terminals.
Connect  a positive  (+)  test  lead from  a  12  VDC
Groundsmaster 300 Series
Page 6A – 11
Electrical System (Rev. G)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website