Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Separating Cutting Unit From Traction Unit (Fig. 14, 15, 16)
1. Position machine on level surface, lower cutting unit
to the shop floor, shut engine off and engage parking
brake.
2. Remove self-tapping screws securing shield to top of
cutting unit and set shield aside.
3. Drive roll pin out of yoke and input shaft of gear box.
Also, loosen cap screws and lock nuts. Slide yoke off
the input shaft. If traction  unit will be used without  the
cutting unit, drive roll pin out of yoke at PTO pivot shaft
and remove entire universal shaft from traction unit.
Figure 14
DANGER
Do not start the  engine and engage the PTO
lever when PTO shaft is not connected to gear
box on  cutting unit. If engine is started and
PTO shaft is allowed to rotate, serious injury
could result.
1. Drive shaft yokes
2. Yokes in phase
3. Roll pin
4. Capscrews
4.
Disconnect cotter pins and clevis pins securing lift
chains to lift arms.
WARNING
Since  the  right  hand  push  arm  is  spring-
loaded  to  about  100  pounds  and  left  hand
push  arm   is  spring-loaded   to  about  150
pounds, a helper is needed to release push
arms from cutting unit. Sudden release of the
push arms could cause injury.
Figure 15
1. R.H. push arm
2. Caster arm
4. Capscrews and washers
5. Ball joint
5. Have a helper push down on the right push arm while
you remove the cap screws, flat washers, lock washers
and  nuts  securing  ball  joint  mount  to  caster  arm  on
cutting unit. Now the helper can carefully allow push arm
to move upward, which will gradually release the 100
pounds of spring load.
3. Ball joint mount
6. Jam nut
6. Have a helper push down on the left push arm while
you remove the cap screws, flat washers, lock washers
and nuts securing ball joint mount to mount bracket on
cutting unit. Now the helper can carefully allow push arm
to move upward which will gradually release the 150
pounds of spring load.
7. Roll the cutting unit away from the traction unit.
Figure 16
1. L.H. push arm
2. Caster arm
5. Capscrews and washers
6. Ball joint
3. Ball joint mount
4. Chain mount
7. Jam nut
Repairs
Page 13 - 12
Groundsmaster® 300 Series
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website