Height of Cut Adjustment (Fig. 6, 7, 8)
The height of cut is adjustable from 1 to 4 inches in
1/2
inch increments, by adding or removing an equal
number of spacers on the front and rear caster forks.
The height of cut chart below gives the combinations of
spacers to use for all height of cut settings.
Height of cut
Spacers Below Caster Arms
Front
Rear
inches
mm
0
1
2
3
4
5
6
0
1
2
3
4
5
6
1
1-1/2
2
2-1/2
3
3-1/2
4
25
38
51
64
76
89
102
NOTE: A more optimum cutting appearance in the 1 inch
height of cut setting can be achieved by lowering the
rear of the cutting unit. Do this by relocating the rear
caster wheel axles in the upper holes of the caster forks.
Install the axles into the lower caster fork holes for
settings above 1 inch.
IMPORTANT: The rear caster wheel mounting hole
in use must be towards the rear of the deck. This is
necessary to provide adequate clearance between
the caster wheel and the mechanical door. If neces
sary, the caster fork assembly should be removed
from the square tube and turned around so that the
mounting hole with the axle through it is toward the
rear. The caster wheel grease fittings should always
face outward.
Figure 6
1. “U” spacers (6)
2. Spacer opening
3. Caster wheel axle holes
4. Mechanical door
IMPORTANT: Do not attempt to cut off more than
one inch of the grass blades in the one (1) inch
height of cut setting with the rear of the cutting unit
lowered, as this may cause the engine to labor
excessively.
1. Start the engine and raise cutting unit so height of cut
can be changed. Stop engine after cutting unit is raised.
2. Squeeze back of wire and rotate wire on lynch pin.
Pull pin out of caster spindle. Slide spacers onto the
caster spindle to get desired height of cut. Then slide
washer onto caster shaft (front only).
Figure 7
3.
Push caster shaft through caster arm. Slide any
remaining spacers onto spindle. Install lynch pin to
retain parts in place. Always have the same number of
spacers on each caster when adjusting height of cut.
1. Thrust washer
2. Lynch pin
3. Spacers (6)
4. Wire spring
Adjustments
Page 12 - 6
Groundsmaster® 300 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 300, Toro Groundsmaster 328 D, Toro Groundsmaster 92801SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews. Need 328D. Manual pdf. Will rate after finding manual
t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems