6.
spindle pulley on the spindle shaft. Slide the pulley off of
the shaft.
Remove the lock nut and flat washer retaining the
4
NOTE: All three spindle housing assemblies are differ-
ent from one another. A spacer is located beneath the
right--hand pulley (Fig. 35).
7.
If the spindle shaft will be replaced, remove the blade
bolt (left hand thread), belleville washer and blade from
thespindleshaft.Otherwise,theblademaybeleftonthe
spindle shaft.
3
5
8.
ing an arbor press. The small bearing spacer should re-
main on the spindle shaft as the shaft is being removed.
Press the spindle shaft out of the spindle housing us-
2
1
9.
The seals will be removed next; however, notice the
Figure 35
orientation of the seal lips. The lips of the lower seals
face outward. On spindle assemblies that have the
grease fitting on the housing (shown in Fig. 36), the lip
of the upper seal faces inward. On spindle assemblies
thathavethegreasefittingonthetopofthespindleshaft
(shown in Fig. 34), the lip of the upper seal faces out-
ward. After noting orientation of seals, remove seals
from the spindle housing.
1.
2.
3.
Left hand spindle
Right hand spindle
Right hand pulley
4.
5.
Left hand pulleu
Spacer
LOCK NUT
FLAT WASHER
CENTER
SPINDLE
PULLEY
10.
of the spindle housing.
Allow the bearings and small thick spacer to fall out
11.
cups out of the spindle housing. Also, drive the large
spacer out of the housing.
Usingapunchandhammer,drivebothofthebearing
UPPER
OIL SEAL
BEARING
LARGE SPACER
SMALL SPACER
12.
and it should remain there because it cannot be easily
removed.
A large snap ring is still inside the spindle housing
SMALL
SNAP RING
LARGE
SNAP RING
IMPORTANT: If new bearings will be installed into a
usedspindlehousingthathastheoriginal snapring
installed, discard the large snap ring that came with
the bearings because it is not needed. However,
new bearings with their matched spacer set and
snapringmustalwaysbeinstalledwhenthespindle
housing is being replaced. Replacement bearings
are sold only with a matched snap ring and spacer
set. These parts cannot be purchased separately.
GREASE
FITTING
BEARING
LOWER
OIL SEAL
CENTER
SPINDLE
BELLEVILLE
WASHER
SPECIAL SCREW
(LEFT HAND THREAD)
Figure 36
Groundsmaster 300 Series
Page 11 -- 27
Rev. I
Repairs
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 300, Toro Groundsmaster 328 D, Toro Groundsmaster 92801SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews. Need 328D. Manual pdf. Will rate after finding manual
t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems