Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Installing Spindle, Bearings
and Seals Into Spindle Housing
IMPORTANT: If a new spindle housing is being used,
new bearings and matched snap ring set must be
installed; see step 1 below. Never use old bearings,
spacer, and snap ring with a new spindle housing.
If installing bearings into a used spindle housing
that  still  has  a snap ring installed, use only new
bearings with cups and spacer – not the large snap
ring because it is not required; see step 2 below.
1. Install large snap ring into groove in bore of spindle
housing. Make sure snap ring is seated in groove.
Figure 30
2. Using an arbor press, push large spacer into top of
spindle housing; tightly against snap ring. The spacer
must contact the snap ring to be sure of the correct
assembly of the parts.
3. Thoroughly oil the bearing cups and using an arbor
press, push the bearing cups, smallest inside diameter
first, into the top and bottom of the spindle housing. The
top bearing cup must contact the spacer that was    in-
stalled  in  step  2,  and  the  bottom  bearing  cup  must
contact the snap ring to be sure of the correct assembly
of parts. Insure that the assembly is correct by support-
ing the first cup and pressing the second against it.
4. Apply a film of grease on lips of both seals, then install
bearing and seal into bottom of spindle housing. Re-
member, the BOTTOM SEALMUSTHAVETHELIPFACING
OUTWARD, not toward the inside of the spindle housing.
Figure 31
5. Check the spindle shaft to make sure it is free of burrs
and nicks that could possibly cut the seals and thor-
oughly lubricate both the shaft and seal lips.
6. Slide small, thick spacer into spindle housing, then
install bearing and seal into top of spindle housing. LIP
OF UPPER SEAL MUST FACE INWARD.
7.
Slide  bearing  spacer  onto  spindle  shaft.  Carefully
slide spindle shaft through spindle housing. The bottom
seal and bearing spacer fit together when the spindle is
installed.
8. Push pulley onto splines of spindle shaft and retain
the parts together with the large flat washer and nut.
Tighten the nut to 100 - 120 ft-lb and rotate the spindle
shaft to be sure that the shaft rotates freely.
9. Slide
pulley end of spindle assembly through hole in
cutting unit. Mount the spindle assembly in place with
the carriage bolts and flange nuts.
10. Install the belt and adjust belt tension.
11. Reinstall the belt covers.
Groundsmaster® 300 Series
Page 13 - 23
Repairs
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website