Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Installing Push Arms,
Torsion Springs and Bushings
1. Apply grease to inside and outside of new bushings.
Using a hammer and flat plate, carefully drive the bush-
ings into the push arm pivot tubes. The bushings must
be flush with the end of the tube.
2. Inspect the torsion springs. If the springs are dam-
aged, use new springs when assembling the parts.
3. Slide the torsion springs onto the inside of the push
arm pivot tubes. Install the washers, push arms with
springs  and  push  arm  brackets  onto  the  pivot  shaft.
Install the roll pins to secure the parts in place.
Figure 24
4.
Raise the push arm and pivot shaft assembly into
position and secure it in place with cap screws, support
plate, reinforcement support and locknuts. Make sure
the springs contact the retainer plate on the push arms
and the underside of the frame.
1. L.H. push arm
2. Caster arm
3. Ball joint mount
4. Chain mount
5. Capscrews and washers
6. Ball joint
7. Jam nut
5. Have a helper push down on the left push arm while
you place a 3 ft. long block of wood between the chassis
and to top of the push arms, across the full width of the
machine.
NOTE: After the wood block is installed, there should be
enough clearance for installing the ball joint into the front
of the push arm.
6.
Thread  jam  nut  fully  onto  the  left-hand  ball  joint.
Screw the ball joint into the left-hand push arm until the
center of the ball joint is 2.25 inches away from the front
of the push arm. Do not tighten the jam nut until the deck
is mounted.
7. Install the brake mount and pedal assembly with cap
screws, locknuts, carriage bolts, lock washer and nuts.
Route the right-hand brake cable through the hole in the
right-hand push arm bracket. Connect the cable to the
brake strut with the clevis   pin and the tension spring.
Hook the opposite end of the tension spring into the hole
in the side of the chassis. Also install the cable into the
mount on the frame.
Repairs
Page 13 - 16
Groundsmaster® 300 Series
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website