Checking and Correcting Mismatch of Blades (Fig. 5)
If there is mismatch between the blades, the grass will
appear streaked when it is cut. This problem can be
corrected by making sure the blades are straight and all
blades are cutting on the same plane.
7. Remove cap screws, flat washers, lock washers and
nuts from outer spindle, in the area where shims must
be added. To raise or lower the blade, add a shim, Part
No. 3256-24, between spindle housing and bottom of
cutting unit. Continue to check alignment of blade and
add shims until tips of blades are within the required
dimension.
1. Using a 3 foot long carpenters level, find a flat surface
on the shop floor.
2.
forks and adjust height of cut so all six height of cut
spacers are below the caster arm.
Set rear caster wheels in the upper hole of caster
IMPORTANT: Do not use more than three shims at
any one hole location. Use decreasing numbers of
shims in adjacent holes if more than one shim is
added to any one hole location.
3. Lower cutting unit onto flat surface. Remove covers
from top of cutting unit. Loosen idler pulleys to release
tension against all three belts.
8. Tension idler pulleys against all three belts. Also
install covers to top of cutting unit.
4. Rotate blades until the ends face forward and back•
ward. Measure from floor to front tip of cutting edge and
remember this dimension. Then rotate same blade so
opposite end is forward and measure again. The differ•
ence between dimensions must not exceed 1/8 inch. If
difference exceeds 1/8 inch, replace the blade because
it is bent. Make sure to measure all three blades.
9. Set rear caster wheels in lower holes in caster forks
if height of cut is above one (1) inch and adjust height
of cut.
10. Mount cutting unit to traction unit: refer to Mounting
Cutting Unit To Traction Unit
5.
Compare measurements of outer blades with the
center blade. Center blade must not be more than 3/8
inch lower than outer blades. If center blade is more than
3/8 inch lower than outer blades, proceed to step 7 and
add shims between spindle housing and bottom of
cutting unit.
1/8"
6. Rotate blades so tips line up with one another. Tips
of the adjacent blades must be within 1/8 inch of each
other. If tips are not within 1 /8 inch of each other,
proceed to step 7 and add shims between spindle
housing and bottom of cutting unit.
Figure 5
Adjustments
Page 11 - 6
Groundsmaster® 300 Series
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 300, Toro Groundsmaster 328 D, Toro Groundsmaster 92801SL |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews. Need 328D. Manual pdf. Will rate after finding manual
t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems