Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Adjustments
Height of Cut Adjustment (Fig. 3, 4)
The height of cut is adjustable from 1 to 4 inches in
1/2
inch increments, by adding or removing an equal
number of spacers on the front and rear caster forks.
The height of cut chart below gives the combinations of
spacers to use for all height of cut settings.
NOTE: 1/4 inch spacers are available and can be or•
dered  from  your  Toro  distributor   by  Toro  Part  No.
27-1040. (Quantity - 8).
Height of Cut
Spacers Below Caster Arms
Front
Rear
inches
mm
0
1
2
3
4
5
6
0
1
2
3
4
5
6
1
1-1/2
2
2-1/2
3
3-1/2
4
25
38
51
64
76
89
102
Figure 3
NOTE: A more optimum cutting appearance of the turf
can be achieved in the lower heights of cut by lowering
the rear of the cutting unit. Accomplish this by relocating
the rear  caster  wheel axles  in the  upper  hole of  the
caster forks. Replace the axles into the lower caster fork
holes for higher height of cut settings where optimum
cutting appearance is not required.
1. Lynch pin
2. Spacers
3. Thrust washer
4. Large (front)
4. caster spindle
IMPORTANT: Do not attempt to cut off more than
one  inch  of  the  grass  blades  in  the  one  (1)  inch
height of cut setting with the rear of the cutting unit
lowered,  as  this  may  cause  the  engine  to  labor
excessively.
1. Start the engine and raise cutting unit so front caster
height of cut can be changed. Stop engine after cutting
unit is raised. Rear caster height of cut can be changed
with cutting unit lowered.
Figure 4
2. Squeeze back of wire and rotate wire on lynch pin.
Pull pin out of caster spindle. Slide spacers onto the
caster spindle to get desired height of cut. Then slide
washer onto spindle.
1. Lynch pin
4. Washer
5. For 1 in. H.O.C. only
2. Small (rear) caster
3. Spacers
3.
Push caster spindle through caster arm. Slide any
remaining  spacers  onto  spindle.  Install  lynch  pin  to
retain parts in place.
NOTE: When cutting unit is used in 1 inch or 1-1/2 inch
height  of  cut  setting,  front  and  rear  rollers  must  be
positioned in the upper bracket holes.
Groundsmaster® 300 Series
Page 11 - 5
Adjustments
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website