Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Input Shaft/Pinion Gear
The following procedures assume the rear axle assem-
bly has been removed from the machine.
Removal
1.
axle support. Remove the  shims and bearing case O-
ring.
Remove input shaft/pinion gear  assembly from the
7
5
2.
Release the stake washer and remove the locknut.
Remove and discard the stake washer (Fig. 18).
4
3.
Drive the input shaft/pinion gear  out from the outer
bearing cone and  bearing case. Remove  and discard
the oil seal and O-ring.
8
4.
cases for damage  and wear. Replace components  as
necessary.
Inspect  all  gears, shafts,  bearings,  spacers,  and
3
NOTE:  Replacement input shaft/pinion gears are only
available in matched ring and pinion sets.
6
Installation
9
10
NOTE:  When installing new bearing cones, press only
on the inner race of the bearing cone.
11
2
1.
If the inner bearing cone was removed, press a new
bearing cone all the way onto the input shaft/pinion gear.
1
2.
case and install the outer bearing cone.
Place the shaft and bearing assembly in the bearing
Figure 18
7.
8.
9.
10. O-ring
11.  Oil seal
1.
2.
3.
4.
5.
6.
Lock nut
Stake washer
Bearing case
Bearing case O-ring
Inner bearing
Outer bearing
Input shaft/pinion gear
Bearing case shims
Seal collar
NOTE:  The  bearings   must  be   completely  seated.
There should be no input shaft/pinion gear end play.
3.
Coat a new oil seal with grease and install as shown
(Fig. 19).
4.
Coat a new O-ring with grease. Install O-ring in the
oil seal collar, and install the collar.
5.
tight.
Install a new stake washer. Install the lock nut finger
0.040
in. (1.0 mm)
2
1
6.
Set the bearing preload be securing the bearing case
in a vise. Thread a M12 x 1.5 hex head capscrew into the
splined end of the input shaft/pinion gear.
7.
to 0.7 Nm) of force is required to rotate the input shaft/
pinion gear in the bearing case.
Slowly tighten the locknut until 4.0 to 6.0 in-lbs. (0.4
8.
Secure the lock nut with the stake washer.
Figure 19
2.   Bearing case
1.
Oil seal
4
WD Rear Axle (Rev. G)
Page 10.1 – 12
Groundsmaster 328–D
(Dae Dong Axle)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website