Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Blade Spindle Service (Fig. 45, 46, 47)
Removing Spindle Housing Assembly
1. Lower the cutting unit, shut the engine off and engage
the parking brake.
2. Remove deck covers from top of cutting unit. Release
belt tension. Remove belt from spindle to be serviced.
3. Start the engine and raise the cutting unit. Turn the
engine OFF and remove the key from the key switch.
Block up the cutting unit so it cannot fall accidentally.
4.
Using a rag or thickly padded glove, grasp end of
blade. Remove blade bolt,  flat washer, anti-scalp cup
and blade from spindle assembly.
5.
Remove  flange  nuts  and  carriage  bolts  securing
spindle housing to deck. Slide spindle housing assem-
bly out the bottom of the cutting unit.
Disassembly
1. Remove the nut and flat washer retaining the spindle
pulley on the spindle shaft. Slide pulley off of shaft.
2.
Press the spindle shaft out of the spindle housing
using an arbor press. The bearing spacer remains on
the spindle shaft as the shaft is being removed.
3. Remove seals from spindle housing.
4. Allow the bearings and small thick spacer to fall out
of the spindle housing.
Figure 45
5. Using a punch and hammer, drive both of the bearing
cups out of the spindle housing. Also drive the large
spacer out of the housing.
1. Grease fitting
2. Jam nut
3. Washer
9. Spindle shaft
10. Spindle spacer
11. Blade
4. Wave seal
5. Carriage bolt
6. Flat washer
7. Spindle housing
8. Flange nut
12. Anti-scalp cup
13. Flat washer
14. Capscrew
15. Bearing assembly
16. Spacer – matched set
6. A
it  should  remain  there  because  it  cannot  be  easily
removed.
large snap ring is still inside the spindle housing and
IMPORTANT: If new bearings will be installed into a
used spindle housing that has the original snap ring
installed, discard the large snap ring that came with
the bearings because it is not needed. However, new
bearings with their matched spacer and snap ring
must always be installed when the spindle housing
is being replaced. Replacement bearings are sold
only with a matched snap ring and spacer set. These
parts cannot be purchased separately.
Groundsmaster® 300 Series
Page 12 - 31
Repairs
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website