Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

Checking and Correcting Mismatch of Blades (Fig. 5)
If there is mismatch between the blades, the grass will
appear streaked when it is cut. This problem can be
corrected by making sure the blades are straight and all
blades are cutting on the same plane.
proceed  to  step  7  and  add  shims  between  spindle
housing and bottom of cutting unit.
7. Remove cap screws, flat washers, lock washers and
nuts from outer spindle, in the area where shims must
be added. To raise or lower the blade, add a shim, Part
No. 3256-24, between spindle housing and bottom of
cutting unit. Continue to check alignment of blade and
add shims until tips of blades are within the required
dimension.
1. Using a 3 foot long carpenters level, find a flat surface
on the shop floor.
2. Adjust height of cut so all six height of cut spacers are
below the caster arm.
3. Lower cutting unit onto flat surface. Remove covers
from top of cutting unit. Release belt tension.
IMPORTANT: Do not use more than three shims at
any one hole location. Use decreasing numbers of
shims in adjacent holes if more than one shim is
added to any one hole location.
4. Rotate blades until the ends face forward and back-
ward. Measure from floor to front tip of cutting edge and
remember this dimension. Then rotate same blade so
opposite end is forward and measure again. The differ-
ence between dimensions must not exceed 1/8 inch. If
difference exceeds 1/8 inch, replace the blade because
it is bent. Make sure to measure all three blades.
8. Adjust belt tension and install covers.
5.
Compare  measurements  of  outer  blades  with  the
center blade. Center blade must not be more than 3/8
inch lower than outer blades. If center blade is more than
3/8 inch lower than outer blades, proceed to step 7 and
add  shims  between  spindle  housing  and  bottom  of
cutting unit.
1/8"
Figure 5
6. Rotate blades so tips line up with one another. Tips
of the adjacent blades must be within 1/8 inch of each
other.  If  tips  are  not  within  1/8  inch  of  each  other,
Adjustments
Page 13 - 6
Groundsmaster® 300 Series
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website