Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual

9.
Remove the  bevel gear  case/axle case  assembly
NOTE:  Axle bearing  shims are  available in 0.008  in.
(0.2 mm), 0.012  in. (0.3 mm), and  0.020 in. (0.5  mm)
thickness.
from the axle  support. Coat a new O-ring  with grease
and temporarily install the axle cover assembly. Position
a dial  indicator at  the tooths center.  Prevent the  axle
from turning and measure the lower bevel gear to axle
gear backlash (Fig. 12).
11.
27
Tighten axle cover screws from 17 to 20 ft-lbs. (23 to
Nm).
12.Coat
a new O-ring with grease and install the bevel
LOWER BEVEL GEAR BACKLASH:
gear  case/axle  case assembly  on  the  axle  support.
Tighten mounting screws and nuts from 35 to 41 ft-lbs.
(47 to 56 Nm) (Fig. 13).
0.004
to 0.016 in. (0.10 to 0.40 mm)
10.Adjust
backlash by increasing or reducing axle bear-
ing shim thickness (see Axle Shafts in this section of this
manual).
Differential Shafts
The following procedures assume the rear axle assem-
bly has been removed from the machine.
35
to 41 ft–lbs.
to 56 Nm)
(47
Removal
1
6
IMPORTANT:
Do not interchange right and left dif-
5
ferential shafts assemblies.
4
1.
Remove the mounting screws, nuts, and lock wash-
2
ers. Remove the bevel  gear case/axle case assembly
and O-ring from the axle support (Fig. 13).
3
35
to 41 ft–lbs.
to 56 Nm)
2.
axle support.
Mark and pull the differential shaft assembly from the
(47
Figure 13
5.
case assembly
6.
3.
4.
Remove the retaining ring and bevel gear (Fig 14).
Drive the differential  shaft out of the  bearings. Re-
1.
2.
3.
4.
Cap screw
Bevel gear case/axle
O-ring
Lock nut
Lock washer
Axle support
move the bearings and bearing shims.
5.
damage and wear. Replace components as necessary.
Inspect all  gears,  shafts, bearings,  and cases  for
Installation
3
1.
Press bearings onto differential shaft. Place correct
combination of bearing shims in axle support and drive
differential shaft  and bearing assembly  into axle sup-
port.
5
4
2
1
2.
3.
Install bevel gear and retaining ring.
Align differential shaft  splines with differential gear
assembly and slide differential shaft assembly onto axle
support.
Figure 14
4.
axle case assembly (see  Bevel Gear Case/Axle Case
Assembly in this section of this manual).
Coat new O-ring with grease. Install bevel gear case/
1.
2.
3.
Retaining ring
Bevel gear
Differential shaft
4.
5.
Bearing
Bearing shims
4
WD Rear Axle (Rev. G)
Page 10.1 – 10
Groundsmaster 328–D
(Dae Dong Axle)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 402 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(2 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual 5.0 out of 5.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 92801SL Rev I Groundsmaster 300 Series Groundsmaster 328 D Service Manual SKU UPC Model
Michael on Nov 30, 2017. 34974

Need 328D. Manual pdf. Will rate after finding manual


barry on Feb 07, 2013. toro groundsmaster 322d

t has been a very reliable machine but getting parts is hard and not cheap to buy , generic parts has been cost effective and reliable , i am unable to get a wiring circut diagram for this unit as most problems are electrical problems


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website